1.

2010 : A new adaptive generalized predictive control algorithm for nonlinear processes

2.

2007 : Cavity temperature control during the cooling cycle in an injection molding machine using a predictive controller

3.

2006 : Coolant flow rate manipulation for cavity pressure control

4.

2005 : Cavity temperature control in injection molding machine

5.

2005 : Injection velocity control in plastic injection molding

6.

2005 : Cavity temperature control in plastic injection molding

7.

2003 : Process Identification of Barrel Temperature Control in Injection Molding: A MIMO Approach

1.

2019 : Multi-objective Optimization in Drilling Kevlar Fiber Reinforced Polymer Using Grey Fuzzy Analysis and Backpropagation Neural Network–Genetic Algorithm (BPNN–GA) Approaches

2.

2018 : Conceptual machine vision design for day and night based on experiment approach

3.

2018 : Preface: Disruptive Innovation in Mechanical Engineering for Industry Competitiveness

4.

2018 : Sliding mode control as controller for remote control weapon station 12.7mm (RCWS)

5.

2018 : Assessments of forces, surface roughness and chip formation in surface grinding of SKD 61 tool steels using dry and minimum quantity lubrication(MQL) techniques

6.

2018 : Characteristics of natural fiber reinforced composite for brake pads material

7.

2018 : Kinematics, dynamics and state space modeling for a remote control weapon station 12.7mm (RCWS)

8.

2018 : Online dynamic set point weighting PID controller for remote controlled weapon station cal. 12.7 mm

9.

2018 : Design optimization of spatial four cables suspended cable driven parallel robot for rapid life-scan

10.

2018 : Design of auto following quadcopter control system based on dynamic waypoint

11.

2018 : GRG nonlinear tuning method for PID controllers in RCWS 12,7 mm system

12.

2018 : Dimension synthesis of suspended eight cables-driven parallel robot for search-and-rescue operation

13.

2017 : Application of Taguchi-grey method to optimize drilling of EMS 45 steel using minimum quantity lubrication (MQL) with multiple performance characteristics

14.

2016 : Character recognition for Writing Robot Control using ANFIS

15.

2015 : Control simulation of an Automatic Turret Gun based on force control method

16.

2014 : Modal and harmonic response analysis: Linear-approach simulation to predict the influence of granular stiffeners on dynamic stiffness of box-shaped workpiece for increasing stability limit against chatter

17.

2014 : Editorial Note

18.

2014 : Optimization of tool wear, surface roughness and material removal rate in the milling process of al 6061 using Taguchi and weighted principal component analysis (WPCA)

19.

2014 : Multiple performance characteristics optimization in the turning process of AISI H13 tool steel using Taguchi and fuzzy logic

20.

2014 : Multiple performance optimization in the wire EDM process of SKD61 tool steel using Taguchi grey relational analysis and fuzzy logic

21.

2014 : Optimization of recast layer thickness and surface roughness in the wire EDM process of AISI H13 tool steel using Taguchi and fuzzy logic

22.

2014 : Preliminary study on magnetic levitation modeling using PID control

23.

2013 : Optimization of multiple performance characteristics in the wire EDM process of AISI D2 tool steel using Taguchi and fuzzy logic

24.

2013 : The use of taguchi-grey-fuzzy to optimize performance characteristics in turning of AISI D2

25.

2013 : Simulation of metal flow to investigate the application of antilock brake mechanic system in deep drawing process of cup

26.

2013 : Optimization of surface roughness and recast layer thickness in the Wire-EDM process of AISI D2 tool steel using Taguchi-grey-fuzzy

1.

2007 : An investigation on the application of predictive control for controlling screw position and velocity on an injection molding machine

2.

2007 : A new scheme for controlling part cooling in injection molding

3.

2006 : Cavity pressure control during cooling in plastic injection molding

4.

2006 : Development of characteristic equations and robust stability analysis for SISO move suppressed and shifted DMC

5.

2006 : A generic controller for part surface temperature on a plastic injection molding machine

6.

2005 : Development of characteristic equations and robust stability analysis for MIMO move suppressed and shifted DMC

7.

2004 : Well-conditioned model predictive control

8.

2002 : A novel tuning method for predictive control of melt temperature and plastication screw speed in injection molding

1.

2017 : Parametric beam modeling to predict the first natural bending frequency of thin wall box-shaped structures verified using experimental modal analysis

2.

2016 : Modelling and simulation analysis of solenoid valve for spring constant influence to dynamic response

3.

2016 : Multi response optimization in face milling process of assab xw-42 tool steel with liquid nitrogen cooling using taguchi-grey-fuzzy method

1.

2019 : Penguatan Kemampuan IKM Komponen Otomotif Pasindo PasuruanMelalui Penyediaan Marketplace “otomotif-its[dot]com� dan Pelatihan Teknik Reverse Engineering

2.

2019 : PELATIHAN KETRAMPILAN LAS LISTRIK UNTUK MASYARAKAT SEKITAR KAMPUS ITS

3.

2018 : Peningkatan Pengetahuan Proses Manufaktur (P3M) SMK

4.

2016 : Pelatihan Pembuatan Biodiesel dari Tanaman Jarak dan Minyak Jelantah untuk Bahan Bakar Mesin Diesel

5.

2015 : Pelatihan Pembuatan Turbin Mikrohidro di Saluran Irigasi untuk Pembangkit Listrik Tenaga Air Skala Kecil

1.

2019 : Penguatan Kemampuan IKM Komponen Otomotif Pasindo PasuruanMelalui Penyediaan Marketplace “otomotif-its[dot]com� dan Pelatihan Teknik Reverse Engineering

2.

2019 : PELATIHAN KETRAMPILAN LAS LISTRIK UNTUK MASYARAKAT SEKITAR KAMPUS ITS

3.

2018 : Peningkatan Pengetahuan Proses Manufaktur (P3M) SMK

4.

2016 : Pelatihan Pembuatan Biodiesel dari Tanaman Jarak dan Minyak Jelantah untuk Bahan Bakar Mesin Diesel

5.

2015 : Pelatihan Pembuatan Turbin Mikrohidro di Saluran Irigasi untuk Pembangkit Listrik Tenaga Air Skala Kecil